Welcome To Snow Foam

Welcome to a new world of cleaning.

First off, we're so happy you're here! If you're anything like us, we love our cars and love keeping them in tip-top condition. As you've now upgraded your car care to Snow Foam, let's delve into making your car care experience better than it ever was before by learning how to use them the way they're intended to. We all have our ways of doing things, so if an alternate way works for you, go for gold!

Car Washing 101

1. Wash In Shade

You don't want soap, water, waxes or sealants to be frying on your hot car panels. This can leave unwanted streaks and makes it even more work to get your car clean.

Try your best to find shade or work during the morning or toward sunset when the sun isn't as harsh if you cannot find shade.

2. Toss Your Old Gear

Old, dried up, dirty towels, wash mitts or chamois can contain used chemicals along with not being super soft on your paint.

Do yourself a favour and keep your cloths, mitts, chamois and towels all clean or replace them. You don't want that rubbing up against your expensive paintwork.

3. Ensure The Car is Cool To Touch

It's best to avoid washing your car straight after a drive. The engine is hot so therefore your bonnet will be hot and your wheels and brakes will be radiating heat too.

Applying wheel cleaners or Snow Foam on these areas is similar to washing the car in the sun.

4. If you drop it, wash it

Avoid dropping any equipment meant for your car's paint. Even though you might be tempted to quickly brush it off and reuse it, this can actually cause more harm than good.

Take your time and grab a new cloth or wash mitt or thoroughly clean it. The amount of dirt on the ground on these cloths can include dirt, rocks, sand and these will lead to endless swirl marks. 

5. Separate Your Towels 

To ensure proper care, avoid using the same towel to dry both your car and your wheels. Similarly, use a different microfiber cloth for the exterior and the interior. This prevents any unintended chemical transfer to surfaces. Take your time and follow these guidelines for optimal results.

Snow Foam Detergents

  • Snow Foam Detergent

  • Berry Thick Detergent

  • Fourby Foam

  • Salt Cleanse

  • Australian Made
  • Ceramic Coating Safe
  • pH Neutral
  • Leaves a great shine finish
  • Requires only 100mL of Detergent mixed with 900mL water
  • Safe on wraps, ppf, vehicle signage
  • Thickness - Lasts up to 5 minutes
  • Australian Made
  • Ceramic Coating Safe
  • pH Neutral
  • Strong Cleaning Capabilities
  • Requires only 100mL of Detergent mixed with 900mL water
  • Safe on wraps, ppf, vehicle signage
  • Thickness Extreme Foam Thickness lasting up to 10 minutes
  • Australian Made
  • Alkaline Formula To tackle dirt, salt, mud and grime
  • Requires only 100mL of Detergent mixed with 900mL water
  • Foam Thickness - Medium
  • Australian Made
  • Coating Safe
  • pH Neutral
  • Tackles salt deposits and staining
  • Requires only 100mL of Detergent mixed with 900mL water

Ultimate Kit Washing Guide

1. Interior Cleaning

Simply apply a fine mist of Interior Cleaner onto the dashboard, trims, and fabric to effectively remove dirt and grime from your interior. Then, use a microfibre cloth to easily wipe off the residue and enjoy the pleasant, clean fragrance.

To achieve a deeper level of cleaning, try agitating the Interior Cleaner with either a brush or drill brush. Afterwards, you can easily remove it using an extractor or wet vacuum.

We like to do the interior first so we aren't stepping into the car with wet feet or hands.

For deeper carpet stains, try Orange and a wet vacuum/extraction.

2. Wheel Cleaning

Attend to wheels with Wheel Cleaner or Purple. Spray on and rinse off within 30 seconds - 60 seconds.

Scrub with Microfibre brush or Bristle Brush as necessary.

For Wheel Cleaner, you want to avoid any raw metal or polished metal and stick to OEM wheels.

For raw aluminium lips or barrels, use Purple.

Use the Microfibre Wheel Brush to get into spokes and barrels whilst the Red Bristle Brush can be used for wheel faces.

3 - Snow Foam Initial Prewash Layer > Dwell > Rinse

Snow Foam the car with 100mL of Snow Foam Detergent and 900mL water in your Snow Foam Lance or Gun. Allow to dwell for 5 - 10 minutes before rinsing.

Best to foam bottom up so that any foam run off doesn't disrupt the foam sticking to the car. 

Let it dwell on the car for 5 - 10 minutes before rinsing.

4 - Snow Foam Contact Layer

With the remainder of the detergent in your Snow Foam Lance or Gun, perform a second layer. This layer will be scrubbed gently with the Snow Cloud Wash Mitt. Rinse thoroughly.

​It is advised from here to setup your Wash and Rinse Two Bucket method, ensuring you clean your mitt after each panel. Alternatively, wash your mitt with your pressure washer after each panel. 

During this stage, you can use ORANGE degreaser on your exhaust tips and side steps before agitating.

5 - Snow Foam Shield Hydrophobic Spray

Whilst the car is wet, mist on a layer of Shield Spray on all panels.

For best results, use a microfibre cloth to spread the product evenly on all panels.

Rinse thoroughly after 30 - 60 seconds. 

6 - Dry with Twister Towel

Lay the towel on the roof of the car flat and pinch two corners of the towel before sliding the water off. 

Ensure the towel doesn't hit the ground nor is used to clean any areas that you may have missed.

Simply go back over any dirty areas with the wash mitt and soap.

7  - Finishing Touches

The car is now dry and you can apply Spray Wax for a shiny final finish - Spray and buff into each panel until dry.

Tyre Gel on the tyres for a satin shine. Apply with Tyre Gel Applicator. Tyre Shine will be a spray application that will leave a wet look.

Clear Window Cleaner to finish up the windows.

8 - Clean Your Microfibre Towels

Ensure you pop your towels and brushes into the wash and look for Microfibre Wash to have them ready for your next wash.

How To Setup The Snow Foam Gun

Setting Up The Snow Foam Gun

Firstly ensure that all parts of the Snow Foam Gun are tight including the gold quick release adaptor and the hose end. You can rotate the hose trigger adjustor to ensure it is to your liking.

From here, simply plug the Snow Foam Gun into your garden hose like you would with any other garden hose accessory, ensure it is tight. 

Using The Snow Foam Gun

Place 800ml of warm water followed by 100mL of Snow Foam Detergent into your bottle.

Screw the bottle onto your Snow Foam Gun's body and attach the quick release adaptor on your garden hose trigger to the body by pulling back on the black ring. Squeeze the trigger and off you go. 

Three Types of Spraying Modes

You can rinse, foam and jet spray with the Snow Foam Gun. For rinsing, take off the Snow Foam Gun body and use the trigger handle to rinse the car.

Attach the Snow Foam Gun body onto the trigger handle along with the end nozzle for foam.

For jet spraying, keep the body on the trigger, but remove the end nozzle.

Adjusting the Dial

With our latest model of Snow Foam Guns, slide the adjusting bar to the largest inlet hole for more foam.

Ensure the holes are facing directly up to ensure the detergent can enter the gun body correctly.

The holes represent mixing ratios:
1:10 , 1:20, 1:32, 1:64, 1:128

How To Use The E-Foamer

Setting Up The E-Foamer

Firstly plug the E-Foamer into a 5V charger with the provided USB Type C charging cable. Open the accessories bag to find two rubber gaskets which will be used before inserting the Foam Nozzle or the Spray Nozzle. 

To Foam: Fill the E-Foamer up with 1950mL of water and 50mL of Snow Foam Detergent and screw the head to the bottle tightly. Ensure the foaming nozzle and gasket are installed to the head. Screw the head on and press the ON button.

To Mist: Swap the Foaming Nozzle to the Misting Nozzle ensuring the gasket is used. Fill the E-Foamer with your favourite Snow Foam solutions and mist away with the trigger. 

There is no need to manually pump the E-Foamer. 

Continuous Foam & Mist

Simply double tap the power button to activate the continuous spray mode.

Press once to turn it off

Chemical Suitability

You can use a vast variety of your favourite Snow Foam products such as Snow Foam Detergent, Orange Degreaser, Purple, Wheel Cleaner, Interior Cleaner, APC and more.

Be sure to stay away from alcohol, corrosive and acidic based chemicals especially when undiluted.


It is advised to clean out the E-Foamer after each use.

Take the head off and run clean water through the E-Foamer head until all chemicals are cleared out of the system.

How To Setup Your Snow Foam Lance

How To Use The Snow Foam Lance

1. Setting Up The Adaptor

Ensure you use the PTFE tape around the thread of the male-to-male adaptor which attaches to the brass body of your Snow Foam Lance. Screw your adaptor on tightly and make sure the tube is connected to the brass Lance head.

For Karcher owners, ensure the two wings of the adaptor point directly up and down to ensure the Lance is straight when plugged in. 

2. Connecting the Snow Foam Lance to your Pressure Washer

Your pressure washer handle will have a detachable spraying wand near where you pull the trigger to release the water. Usually you will need to push this attachment toward you, twist and the attachment will release. Where this sprayer wand is attached to is where your Snow Foam Lance will go.

Some pressure washer models have two sections that can be detached such as the Gerni brand, so ensure it is the attachment as close to your trigger hand is, not the furthest one. 

3. Using the Snow Foam Lance

  • Fill the Snow Foam Lance bottle with 900mL of warm water followed by 100mL of your favourite Snow Foam Detergent.

We have our original Snow Foam Detergent, Snow Foam Berry Thick, Fourby Foam and Salt Cleanse.

Give it a quick shake and spray your car from bottom up.

Ensure the top dial is set toward negative (-) which means less water and more soap. Then hold the end of your Snow Foam Lance (either the long red or black part) and rotate it slowly to get your desired spray pattern

4. Washing The Car, Bike or Boat

We foam the vehicle from bottom up ensuring we don't miss any sections. We like the wider spray pattern to get an even coverage of foam on the vehicle.

We let this dwell for 5-10 minutes before a thorough rinsing. We then apply a second layer and proceed with a two-bucket-wash method to ensure all the stubborn dirt and grime is off the car as safely as possible. 

Snow Foam Lance Adaptor

Short Trigger Gun + Snow Foam Switch Setup

Setting Up The Short Trigger Gun

If you have been given a small cube box with an adaptor in it, you will need to use PTFE tape around the brass thread of your Short Trigger Gun approximately 5-8 revolutions. Screw this adaptor onto your Short Trigger Gun and tighten.

If you are using an M22 adaptor, simply PTFE tape the brass thread on the end adaptor.

Proceed to click in your pressure washer's hose via the adaptor or screw it in via the m22 adaptor.

Screw the gold quick connector adaptor onto the spray end of the short trigger gun tightly before inserting a coloured spray nozzle.

Spraying The Car

To use the Short Trigger Gun you will need to pull back the gold quick release end and insert one of the coloured nozzles and lock it in tightly. If the nozzle isn't in tightly, you can have this small piece be blasted by the water pressure and cause damage to yourself, other or your car.

For this, shoot at the ground first and never point it directly at another human being or animal. 

Connecting Your Snow Foam Lance

You will need: 1/4 Inch Adaptor

If you are intending to use your Snow Foam Lance with the Short Trigger Gun, you will need to switch the existing adaptor to a 1/4 inch quick connect adaptor. It will then click in and out like the 5 coloured nozzles.

Snow Foam Switch

Plug the Snow Foam Switch system to the female 1/4 inch quick connector. Then connect your Snow Foam Lance to one arm and a coloured sprayer nozzle to the other.

Snow Foam Lance Adaptor
Image Description

How To Use The Underbody Cleaner

Setting Up The Underbody Cleaner

You will receive the Snow Foam Underbody Cleaner, three extension hoses and an adaptor for your pressure washer. 

Simply connect the 1/4 inch connections together (pull back and click in) and connect it to your pressure washer.

Using The Underbody Cleaner

Roll the Underbody back and forth underneath your car to get as much dirt, sand and grime off as you can. 

You can then pull out the swivel pin to adjust the angle as desired.

Driveway Cleaning

Simply rotate the Underbody Cleaner to have the spray heads pointing towards the ground.

Roll back and forward to clean your driveway.

Image Description

How To Use Your Exterior Care Products

  • Apply to clean and cool surfaces
  • Perform cleaning in shade
  • Avoid wax based products on Ceramic Coated Cars
  • Always test on an inconspicuous area before proceeding.

Gloss Wash

  1. Use a two-bucket wash method and add 50mL per 10L bucket into your wash bucket
  2. Using a wash mitt, scrub vehicle from top to bottom. Rinse in rinse bucket.
  3. Rinse car and dry with Twister Towel or Waffle Weave Towel
  4. Allow the full gloss effect to come to life 8 - 12 hours post wash

Gloss Wash contains lanolin waxes in it and should not be used on some ceramic coatings or vinyl wraps. 

Ceramic Detailer

Ceramic Detailer is the dry-apply equivalent of Snow Foam Shield range. In shade, after a wash, simply mist on to each panel and buff off to unleash an intense shine and hydrophobic finish. Always use clean microfibre cloths.

Quick Detailer

Quick Detailer is a surface spot treatment to remove contaminants before they can bond to your paint. Spray onto the contaminated surface, and wipe with a folded microfibre cloth, then dry with the other clean side.

Shield Hydrophobic Spray

After washing your car and the panels are still wet, spray Snow Foam Shield on your clean panels and wipe in with a clean microfibre cloth. Apply when wet and rinse off before drying.

Shield Hydrophobic Concentrate

Applicable by Snow Foam Lance, 100mL of Snow Foam Shield with 900mL water will give your car the hydrophobic finish you've been looking for! Apply when wet and instantly rinse off before drying.

Spray Wax

Achieve a stunning, glossy finish on your car's paint with Spray Wax, featuring a high-grade wax formulation in an easy-to-use spray.

Mist on and gently buff off until all residue is gone.

Spray Wax

Achieve a stunning, glossy finish on your car's paint with Spray Wax, featuring a high-grade wax formulation in an easy-to-use spray.

Mist on and gently buff off until all residue is gone.

Clear - Window Cleaner

After washing your car, spray Clear directly onto windows or onto clean microfibre cloth. Gently rub until clean.

Repeat on all windows ensuring you switch to clean sections of the microfibre towel.

Tar Remover

Simply spray on and let it break down the tar and agitate if needed. Using a detailing brush can assist in removing stubborn tar. Rinse thoroughly.

Black Trim Restorer

Apply to clean and cool surfaces.

1. Shake well before use.

2. Apply a small amount to the applicator.

3. Spread evenly until the surface is evenly coated.

4. Allow a dwell time of 1 - 2 minutes.

5. Wipe away any excess from the surface with a clean cloth.

6. Allow drying for up to 1 hour to a natural new finishing look.

Purple - Iron Dissolving Wheel Cleaner

Always test on an inconspicuous area before proceeding.

1. Spray wheels when car is dry. Best to leave car to cool down and ensure you do not miss any smaller curves on the wheel's design.

2. Let Purple dwell and dissolve the brake dust. When you see the purple bleeding, this is when you know it is time to rinse.

3. Rinse thoroughly ensuring all product is rinsed off

4. Check wheels, follow with light scrubbing if needed.

5. Dry wheels and proceed to use Tire Shine. 

Wheel Cleaner

1. Spray wheels when car is dry. Best to leave car to cool down and ensure you do not miss any smaller curves on the wheel's design.

2. Let Wheel Cleaner dwell and dissolve the brake dust. Only needs 30-60 seconds of dwell time.

3. Rinse thoroughly ensuring all product is rinsed off

4. Check wheels, follow with a second layer with light agitation with wheel brush if needed.

5. Dry wheels and proceed to use Tire Shine. 

As an alkaline-based solution, avoid using Wheel Cleaner on polished or raw aluminium wheels as bleaching may occur. Always test on an inconspicuous area before proceeding.

Tyre Shine

Simply mist onto your clean tyres and if needed, spread across tyre to even out the shine. Wipe any overspray and leave to settle in before driving away. You will now have tyres looking refreshed and ready for the road or show and shine.

Tyre Gel

Simply use a coin-sized amount onto a clean tyre applicator and apply onto your clean tyres. Swipe across tyre face ensuring you haven't missed any spots. You will now have tyres looking refreshed and ready for the road or show and shine.

How To Use Your Interior Care Products

Interior Cleaner

Simply mist spray onto your dashboard, trims and fabric and say goodbye to your interior dirt and grime. Simply wipe off with a microfibre cloth and breath in the pleasant, clean fragrance. 

Interior Cleaner can be agitated with a brush or drill brush for deeper cleaning and removed with an extractor or wet vacuum.

Fresher Leather

Simply mist spray onto your seat one section at a time and agitate with a brush or cloth. Wipe off with a clean microfibre cloth. 

Best used after Interior Cleaner 

Interior Trim Rejuvenator

Clean interior plastics with Snow Foam Interior Cleaner

Apply a coin sized amount of Interior Trim Restorer onto a clean microfibre cloth or pad

In a circular motion, work at the interior plastics ensuring an even finish

Using a clean microfibre cloth, wipe over the area

Fresh Linen Air Freshener

Vacuum carpets and spray 5 - 10 times on floor mats. Repeat when smell fades.

Avoid spraying on pedals.